2007-2019 Ford Mustang TPMS Light Tire Pressure System Reset
Last Updated on January 15, 2020 by Christ
2007-2019 Ford Mustang TPMS Light Tire Pressure System Reset – After approximately 50 years of marketing only to meet the North American market share alone, is now the latest edition Mustang was designed and manufactured to meet more than 100 markets globally, with first deliveries targeted to Asia. Two variants of the Ford Mustang, hardtop and convertible, which has been submitted in accordance with road conditions in Asia and the speed limit and the defined security of European countries.
The engineers at Ford have confirmed that the construction of this sixth-generation Mustang has met the requirements set in the destination countries. Global expansion is done, eventually making the Ford Mustang produce the right wheel to meet 25 new markets, including the UK, Australia, and South Africa. Ford also ensure that the Mustang is released into the global market will still maintain the hallmark of America, as the key to their sales. As for the engine variant, the Ford Mustang is available in two types, standard engine V6 EcoBoost 4-cylinder or V8 high-performance engine.
2007-2019 Ford Mustang TPMS Light Tire Pressure System Reset:
If you receive a low-tire-pressure monitoring system (TPMS) warning light while driving and you want to clear or turning off the warning light on your 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 Ford Mustang, follow these instructions:
- Make sure the vehicle is at a complete stop
- Turn the engine switch off
- Adjust the tire inflation pressure recommended on the tire placard located on the door panel.
- Driving for a few miles (kilometers), calibration will complete after 2 minutes of cumulative driving at 20 mph (32 km/h).
Time needed: 17 minutes
If you replaced a wheel, tire, TPMS sensor, etc. and are now getting a warning light on your car, then the sensor needs to be reset. For that you need to purchase the correct TPMS reset tool and follow these instructions:
- Stop the vehicle in a safe place and turn the engine switch off and engage the parking brake.
- Press and release the brake pedal.
- Turn the ignition from OFF to ON position three (3) times ending in the on position without starting the engine.
If your car has a Smart key button, press once to turn on, then press again to put the vehicle into ACC mode, then press again to turn the vehicle off. Repeat 2 more times, ending in ACC mode.
- Press the brake pedal again for 2 seconds, then release.
- Turn the ignition to OFF position (DO NOT remove the key)
- Turn the ignition from OFF to ON position three (3) times ending in the on position without starting the engine
- If the reset mode has been entered successfully, the horn will sound once.
- Starting from the driver’s side front tire, place the relearn tool against the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor.
- Repeat the procedure on the right-front tire, the right rear tire, and the last one left rear tire.
- A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.
- After hearing the confirming horn chirp for the left rear tire, training is completed and a message is shown in the information display. Turn ignition to OFF position. Adjust all tires to pressure listed on tire placard.
For more details, please watch the following video:
This tutorial is based on the Ford owner’s manual. This procedure should be work on the latest generation of Ford Mustang (2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 model years). Hopefully, the article of 2007-2019 Ford Mustang TPMS Light Tire Pressure System Resets useful for you. Good Luck!
Bought a brand new 2016 Mustang in Australia 2 days ago. Tire pressure monitor will not come on on dashboard display. I go Driver Settings-OK-Tire Pressure-OK and then all I get is a display saying Hold OK to Reset. I do that, as there are no other options, it resets … and I still get no tire pressure readout for all four tires. All I get is the Hold Ok to Reset msg again. When I was shown this at the dealer 2 days ago, it worked, so what am I doing wrong? All I’ve done since is added air to the tires.
Ok they totally gave direction for this procedure the long complicated way. All you have to do it is while the car is off press the acc/power button without your foot on the break peddle. Now that you have power press the hazard button three time. The car will honk and will enter tire training mode. That is it.
Thank you
I programed the tire pressure monitoring system . Then the Antilock Break system and anti traction system light went out as soon as I started driving
I had a tire fixed. They said they replaced a tire sensor. The light came on saying I had a bad tire sensor. I ordered the remote to program the system. Before it came anti lock and traction codes popped up. I filled these simple directions now I have no codes and did not have to put our mustang in the shop.
Thanks guys
TD