How To Reset Lincoln MKX TPMS Tire Pressure Monitoring Sensor Light

Last Updated on December 5, 2020 by Christ

How To Reset Lincoln MKX TPMS Tire Pressure Monitoring Sensor Light – The Lincoln MKX is a mid-size luxury crossover car produced by Lincoln since 2007. The MKX debuted in December 2006 for the 2007 model year. It was prefigured by a concept car that was unveiled to the public at the 2004 Detroit Car Show. The MKX is basically a Ford Edge version obtained through badge engineering and is built on Ford’s CD3 platform similar to the model mentioned and the Mazda CX-9. The MKX has a five-door crossover bodywork.

The model is equipped with a monocoque structure and is front-wheel drive. But, among the options, there is the full traction. The MKX has installed a V6 Duratec 3.5-liter cylinder engine, coupled to a six-speed automatic transmission. The engine is entirely made of aluminum and emits 265 hp of power at 6,250 pm and 340 Nm of torque at 4,500 pm. The MKX is assembled in Oakville, Canada, and has been facelifted in 2011.

How To Reset Lincoln MKX TPMS Tire Pressure Monitoring Sensor Light

How To Reset Lincoln MKX TPMS Tire Pressure Monitoring Sensor Light

If you receive a low-tire-pressure monitoring system (TPMS) warning light while driving and you want to clear or turning off the warning light on your 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 Lincoln MKX, follow these instructions:

  • Make sure the vehicle is at a complete stop
  • Turn the engine switch off
  • Adjust the tire inflation pressure recommended on the tire placard located on the door panel.
  • Driving for a few miles (kilometers), calibration will complete after 2 minutes of cumulative driving at 20 mph (32 km/h).

Time needed: 7 minutes

If you replaced a wheel, tire, TPMS sensor, etc. and are now getting a warning light on your car, then the sensor needs to be reset. For that you need to purchase the correct TPMS reset tool and follow these instructions:

  1. Stop the vehicle in a safe place and turn the engine switch off and engage the parking brake.

  2. Press and release the brake pedal.

  3. Turn the ignition from OFF to ON position three (3) times ending in the on position without starting the engine.

    If your car has a Smart key button, press once to turn on, then press again to put the vehicle into ACC mode, then press again to turn the vehicle off. Repeat 2 more times, ending in ACC mode.

  4. Press the brake pedal again for 2 seconds, then release.

  5. Turn the ignition to OFF position (DO NOT remove the key)

  6. Turn the ignition from OFF to ON position three (3) times ending in the on position without starting the engine.

  7. If the reset mode has been entered successfully, the horn will sound once.

  8. Starting from the driver’s side front tire, place the relearn tool against the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor.

  9. Repeat the procedure on the right-front tire, the right rear tire, and the last one left rear tire.

  10. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.

  11. After hearing the confirming horn chirp for the left rear tire, training is completed and a message is shown in the information display. Turn ignition to OFF position. Adjust all tires to pressure listed on the tire placard.

For more details, please watch the following video:

This tutorial is based on the Lincoln owner’s manual. This procedure should be work on the latest generation of Lincoln MKX (2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 model years). Hopefully, the article of How To Reset Lincoln MKX TPMS Tire Pressure Monitoring Sensor Light useful for you. Good Luck!

(Visited 2,323 times, 1 visits today)

Leave a Reply

Your email address will not be published. Required fields are marked *

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.