Subaru Impreza Timing Marks Diagram (2.5L DOHC EJ Engine)

Last Updated on January 23, 2020 by Christ

Subaru Impreza Timing Marks Diagram (2.5L DOHC EJ Engine) – The Subaru Impreza is a compact sedan produced by the Japanese manufacturer Subaru, exit off the production lines for the first time in 1992 and arrived today in its third generation. In 1992, the Impreza was called to replace the now obsolete Subaru Leone, which had maintained despite the presence on the international market for over 20 years. Similarly, it was designed with an eye to the world of ballistic competitions, in which it should have replaced the larger and heavier Subaru Legacy.

By Legacy, the Impreza has undergone inherited the new range of engines called EJ, which replaced the old EA engines. The basic mechanical architecture is the usual home Subaru: longitudinal boxer engine and all-wheel drive (front or on some base models), MacPherson front suspension and rear articulated quadrilateral. These solutions allow to Impreza to have a symmetrical arrangement of the mechanical parts and a very low center of gravity. This means less roll, the lower the “steering torque”, less vibration by the motor (which does not need a balancer).

Subaru Impreza Timing Marks Diagram (2.5L DOHC EJ Engine):

Subaru Impreza Timing Marks Diagram (2.5L DOHC EJ Engine)

1. Arrow mark
2. Timing belt
3. 28 tooth length
4. 54.5 tooth length
5. 51 tooth length
6. 28 tooth length
7. Install it in the end
A. Align mark (A) on the crank sprocket with the mark on the oil pump cover at cylinder block.
B. Align the single line mark (B) on intake cam sprocket (LH) with a notch on the timing belt cover
C. Align single line mark (C) on exhaust cam sprocket (LH) with a notch on the timing belt cover
D. Align single line mark (D) on the intake cam sprocket (RH) with a notch on the timing belt cover.
E. Align single line mark (E) on the exhaust cam sprocket (RH) with a notch on the timing belt cover.

Note: Align the alignment mark on the timing belt with marks on sprockets in the alphabetical order shown in the figure. While aligning marks, position the timing belt properly. This diagram applies to Subaru Impreza WRX STI 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 model years which uses EJ DOHC Engine. For more detail please watch the following video:

A series of horizontal Subaru EJ engine family for the Japanese Fuji Heavy Industries during the 1990s to 2000s on the development and manufacturing of horizontal reciprocating four-cylinder gasoline engine, replacing the previous Subaru EA engine family; this entry is described Subaru Alcyone SVX is equipped with the EG33 type flat-six engine.

Displacement 2,457c.c. The type is from the main engine EJ25 EJ20 type expansion tank comes, bore 99.5mm, stroke 79.0mm. A naturally aspirated version of the compression ratio of 9.5: 1 to 10.0: 1, is a turbocharged version of the 8.0: 1 to 9.5: 1. In the past, mostly DOHC portfolios and naturally aspirated then replaced the existing take SOHC naturally aspirated, DOHC turbocharged ride and other two kinds of combinations. This type of engine with variable valve timing technology for the i-AVLS wisdom valve lifting system, each cylinder intake valve rocker arm with its cam driven by the Ministry. This diagram is based on the Subaru workshop manual. Hopefully the article of Subaru Impreza Timing Marks Diagram (2.5L DOHC EJ Engine) useful for you.

(Visited 2,793 times, 1 visits today)

Leave a Reply

Your email address will not be published. Required fields are marked *

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.