How To Reset Peugeot Traveller Tyre Pressure Warning Light (2016-2020)

Last Updated on January 20, 2020 by Christ

How To Reset Peugeot Traveller Tyre Pressure Warning Light (2016-2020) – The Peugeot Traveler is a van presented by the French car manufacturer Peugeot in March 2016 at the Geneva Motor Show. The vehicle is identical to the Citroën Spacetourer and the Toyota ProAce Verso. All three have been developed jointly by PSA Peugeot Citroën and Toyota and are largely optically and technically related to the Citroën Jumpy3, Peugeot Expert 3 and Toyota Proace2. All models are built at Sevel Nord in the PSA factory in Valenciennes. In the model hierarchy, the Traveler peels the Peugeot 807, built by 2014.

The Vans Spacetourer and Traveler as well as the ProAce Verso, are based on the commercial versions Citroën Jumpy, Peugeot Expert and Toyota Proace. Their predecessor versions were developed by PSA together with Fiat and originated again from the common Eurovan (PSA / Fiat) development, which started in 1994. Fiat joined Fiat Chrysler Automobiles in 2009 with Chrysler. This gave Fiat the opportunity to take Vans from Chrysler for its own model program, while at the same time the market for classic Vans began to shrink as a result of the development towards SUVs. The production of the Fiat Ulysse was therefore discontinued in 2011 and the Lancia Phedra as early as 2010 and both replaced by models of the new group merger.

How To Reset Peugeot Traveller Tyre Pressure Warning Light (2016-2020)

Contents

How To Reset Peugeot Traveller Tyre Pressure Warning Light (2016-2020):

Time needed: 7 minutes

If you replaced a wheel, tire, TPMS sensor, etc. and are now getting a warning light on your car, then the sensor needs to be reset. To reset the Tire Pressure Monitoring System (TPMS) light on your Peugeot Traveller, follow these steps:

  1. Make sure the vehicle is at a complete stop

  2. Turn the engine switch off

  3. Adjust the tire inflation pressure recommended on the tire placard located on the door panel.

  4. Turn the ignition to ON position without starting the engine.

  5. Locate and press the SET button until you hear an audible signal

    Reset Low Tyre Pressure Peugeot

With the Audio System:

  • Stop the vehicle in a safe place and turn the engine switch off
  • Adjust the tire inflation pressure recommended on the tire placard located on the middle pillar, driver’s side.
  • Turn the engine switch to the “ON” position
  • Press the MENU button located on the audio system
  • Highlight the Personalisation-configuration menu by pressing the “<<” or “>>” button
  • Press the “OK” button
  • In the Personalisation, menu select Under-inflation initialisation
  • Press the “OK” button to confirm

With the Touch Screen:

  • Stop the vehicle in a safe place and turn the engine switch off
  • Adjust the tire inflation pressure recommended on the tire placard located on the middle pillar, driver’s side.
  • Turn the engine switch to the “ON” position
  • Press the MENU button located on the audio system
  • Tap the Driving menu
  • Select “Under-inflation initialisation”.
  • Select “Yes” to Confirm

This tutorial is based on the Peugeot owner’s manual. The procedure above can be applied to the latest generations of Peugeot Traveller (2016 2017 2018 2019 2020 model years), which is equipped with a Tire Pressure Monitoring System (TPMS). Hopefully, the article How To Reset Peugeot Traveller Tyre Pressure Warning Light (2016-2020) useful for you.

(Visited 844 times, 1 visits today)

Leave a Reply

Your email address will not be published. Required fields are marked *

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.