Tips

How To Reset GMC Yukon TPMS Tire Pressure Sensor Light (2015-2020)

How To Reset GMC Yukon TPMS Tire Pressure Sensor Light (2015-2020) – The fourth-generation GMC Yukon was introduced in September 2013, went on sale in the first quarter of 2014. It is made in Arlington (Texas). The car is presented in the following versions of the usual GMC Yukon, extended Yukon XL, ordinary in luxury Yukon Denali and extended in luxury Yukon Denali XL.

GMC Yukon and Yukon XL received a new gasoline engine EcoTec3 5.3L V-8 FlexFuel (L83) with 356 hp and 519 Nm of torque. GMC Yukon Denali and Yukon Denali XL received a new petrol engine EcoTec3 6.2L V-8 FlexFuel (L86) with 420 hp and 610 Nm of torque.

Contents

How To Reset GMC Yukon TPMS Tire Pressure Sensor Light (2015-2020)

Time needed: 17 minutes

If you replaced a wheel, tire, TPMS sensor, etc. and are now getting a warning light on your car, then the sensor needs to be reset. To relearn or reset the Tire Pressure Monitoring System (TPMS) sensor on your GMC Yukon you must have a TPMS relearn tool and follow these steps:

  1. Stop the vehicle in a safe place

    Turn the engine switch off and engage the parking brake.

  2. Turn the ignition to the ON position without starting the engine.

    If your car equipped with ignition button, press and hold the Start/Stop button for 5 seconds without touch the brake pedal

  3. Go to INFO menu by using ◄ navigation button

    The button is located on the steering wheel

  4. Scroll to the TIRE PRESSURE menu

    Press the  button to enter the menu

  5. Press and hold the button

    The horn sounds twice to signal the receiver is in relearn mode

  6. Starting from the driver’s side front tire, place the relearn tool against the tire sidewall, near the valve stem.

    Then press the button to activate the TPMS sensor.

  7. Repeat the procedure on the right-front tire, the right rear tire, and the last one left rear tire.

    A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.

  8. Turn off the ignition

    Press the Start/Stop button once

  9. Adjust the tire inflation pressure recommended on the tire placard located on the door panel.

    Done!

Method 2:

  • Turn the ignition to ON position without starting the engine.
  • Turn the Trip knob until TIRE PRESSURE appears on the display.
  • Press and hold the knob to select the menu
  • Starting from the driver’s side front tire, place the relearn tool against the tire sidewall, near the valve stem.
  • Repeat the procedure on the right-front tire, the right rear tire, and the last one left rear tire.
  • Turn off the ignition
  • Adjust the tire inflation pressure recommended on the tire placard located on the door panel.

These instructions are based on the GMC Yukon owner’s manual. This procedure should apply to the fourth generation of the GMC Yukon (2015 2016 2017 2018 2019 2020 model years). Hopefully, the article How To Reset GMC Yukon TPMS Tire Pressure Sensor Light (2015-2020) can solve your problem. Good Luck!

Christ

Recent Posts

Exploring the Tech-Advanced Safety Features of Honda Civic

When it comes to safety on the roads, nothing beats the sterling integration of technology…

6 months ago

Mastering Car Oil Changes: Crucial for Business Efficiency

Imagine a car engine as the heart of a business. Without proper and regular maintenance,…

6 months ago

Avoiding Common Car Maintenance Mistakes

Maintaining the health of your car is much like maintaining your health. Ignoring minor symptoms…

6 months ago

Petrol vs Diesel: Unravelling the Used Jeep Wrangler Conundrum

The quest to find the perfect engine variant, when in the market for a used…

6 months ago

Mastering DIY Checks for a Used Jeep Wrangler

When it comes to advancing your automotive acumen, understanding the ins and outs of purchasing…

7 months ago

Key Maintenance Tips for Used Jeep Wranglers

Jeep Wranglers, known for their robust character and off-road prowess, can prove to be resilient…

7 months ago

This website uses cookies.