2006-2019 Ford Explorer TPMS Light Low Tire Pressure Reset
Last Updated on February 17, 2020 by Christ
2006-2019 Ford Explorer TPMS Light Low Tire Pressure Reset – In the event, the Los Angeles Motor Show 2014, Ford will launch the Ford Explorer 2016. Cars that get into the SUV segment has received several changes from various sides and also added one new type that is Platinum. Explorer is the core of Ford’s global vehicle because he was able to provide the ideal combination of performance and functionality. Because it is not surprising that at least the car is already sold 7 million units.
Various changes have been made. Among the most crucial is the engine. The EcoBoost engine capacity of 2.3 liters is believed to replace the 2.0-liter EcoBoost engine. With this new engine, the car has the right to get the power up to 270 hp and torque of 406 Nm. In addition, Ford deliberately adds one more type for the Ford Explorer, Platinum. It is considered reasonable given the type of market many who want more luxurious than it already is.
2006-2019 Ford Explorer TPMS Light Low Tire Pressure Reset:
If you receive a low-tire-pressure monitoring system (TPMS) warning light while driving and you want to clear or turning off the warning light on your 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 Ford Explorer, follow these instructions:
- Make sure the vehicle is at a complete stop
- Turn the engine switch off
- Adjust the tire inflation pressure recommended on the tire placard located on the door panel.
- Driving for a few miles (kilometers), calibration will complete after 2 minutes of cumulative driving at 20 mph (32 km/h).
Time needed: 17 minutes
If you replaced a wheel, tire, TPMS sensor, etc. and are now getting a warning light on your car, then the sensor needs to be reset. For that you need to purchase the correct TPMS reset tool and follow these instructions:
- Stop the vehicle in a safe place and turn the engine switch off and engage the parking brake.
.
- Press and release the brake pedal.
.
- Turn the ignition from OFF to ON position three (3) times ending in the on position without starting the engine.
If your car has a Smart key button, press once to turn on, then press again to put the vehicle into ACC mode, then press again to turn the vehicle off. Repeat 2 more times, ending in ACC mode.
- Press the brake pedal again for 2 seconds, then release.
.
- Turn the ignition to OFF position
DO NOT remove the key
- Turn the ignition from OFF to ON position three (3) times ending in the on position without starting the engine.
If your car has a Smart key button, press once to turn on, then press again to put the vehicle into ACC mode, then press again to turn the vehicle off. Repeat 2 more times, ending in ACC mode.
- If the reset mode has been entered successfully, the horn will sound once.
.
- Starting from the driver’s side front tire, place the TPMS RELEARN TOOL against the tire sidewall, near the valve stem.
Then press the button to activate the TPMS sensor.
- Repeat the procedure on the right-front tire, the right rear tire, and the last one left rear tire.
A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.
- After hearing the confirming horn chirp for the left rear tire, training is completed and a message is shown in the information display.
.
- Turn ignition to OFF position. Adjust all tires to pressure listed on the tire placard.
.
For more details, please watch the following video:
We got this tutorial from Ford specialists. This procedure should be work on the latest generation of Ford Explorer (2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 model years). Hopefully, the article of 2006-2019 Ford Explorer TPMS Light Low Tire Pressure Reset useful for you. Good Luck!
Leave a Reply