Reset Tire Pressure Sensor (TPMS) on 2012-2016 Chevy Cruze

Reset Tire Pressure Sensor (TPMS) on 2012-2016 Chevy Cruze – The Chevrolet Cruze is average car produced since 2009 by the Korean automaker Daewoo (now GM Korea as part of the US group General Motors). The car replaces the Chevrolet Lacetti in Europe, while in the Asian markets is sold under the name Daewoo Lacetti Premiere and Australia is known as the Holden Cruze. The Cruze was created to replace many models (over the Nubira) products around the world, such as the Chevrolet Cobalt sold in the US alone, the Australian Holden Viva, the Pontiac G5 sold in the Americas and the Chevrolet Optra sold in emerging countries.

The new world car in addition to adopting a single designation depending on the manufacturer brand has been designed on a totally new platform (chassis Delta II) developed by the Opel engineers to fit even on the fourth generation of the Astra. The design anticipates the lines of future cars of the mark, characterized by a frontal angular equipped with a large mask, elusive headlights and ribs on the hood. The tail has a much more traditional lights vaguely inspired by the German competition. About 4.60 meters long the new Cruze adopts a scheme of simple and inexpensive to produce suspensions configured as MacPherson for the front and a torsion beam at the rear. The body structure has also been designed to obtain the maximum score in EuroNCAP safety tests.

How to Reset Tire Pressure Sensor (TPMS) on 2012-2016 Chevrolet Cruze:

If you receive a low-tire pressure monitoring system (TPMS) warning light while driving and you want to clear or turning off the warning light on your 2012 2013 2014 2015 2016 Chevy Cruze, follow these instructions:

  • Make sure the vehicle is at a complete stop
  • Turn the engine switch off
  • Adjust the tire inflation pressure recommended on the tire placard located on the door panel.
  • Driving for a few miles (kilometers), calibration will complete after 2 minutes of cumulative driving at 20 mph (32 km/h).

If you replaced a wheel, tire, TPMS sensor etc. and are now getting a warning light on your car, then the sensor need to be reset. To relearn or reset the Tire Pressure Monitoring System (TPMS) sensor on your 2008 2009 2010 2011, 2012, 2013, 2014, 2015 2016 2017 Chevy Cruze you must have a TPMS relearn tool and follow these steps:

  • Stop the vehicle in a safe place and turn the engine switch off and engage the parking brake.
  • Turn the ignition to position On without starting the engine.
  • Press and hold unlock and lock buttons on the Remote Keyless Entry (RKE) transmitter until horn sounds
  • If your vehicle does not have Remote Keyless Entry (RKE) transmitter
    • Press the DIC MENU button
    • Scroll up and select “Tire Pressure Menu”
    • Press the SET/CLR button
    • When a message requesting acceptance of the process appear, press the SET/CLR button again to confirm.
    • The horn sounds twice to signal the receiver is in relearn mode
  • Starting from the driver’s side front tire, place the relearn tool against the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor.
  • Repeat the procedure on the right-front tire, the right rear tire, and the last one left rear tire.
  • A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.
  • Turn the ignition off and start the engine to verify the indicator has been reset.

For more details, please watch the following video:

This procedure should be work on latest generation of Chevy Cruze (2012 2013 2014 2015 2016 2017) model years. Hopefully the article of Reset Tire Pressure Sensor (TPMS) on 2012-2016 Chevy Cruze usefull for you. Good Luck!

(Visited 18,888 times, 7 visits today)
Tagged with: , ,

Leave a Reply

Your email address will not be published. Required fields are marked *


This site uses Akismet to reduce spam. Learn how your comment data is processed.