How To Reset Maintenance Service Light on Volvo V60 (2011-2021)
Last Updated on March 27, 2021 by Christ
How To Reset Maintenance Service Light on Volvo V60 (2011-2021) – The Volvo V60 is a station wagon produced by the Swedish car manufacturer Volvo in Torslanda since September 2010. The V60 is built on the shortened wheelbase chassis of the flagship S80 (the Y20 platform also used by the V70 and XC60).
The car has a five-door, five-seater bodywork, and its exterior lines straddle the D-segment and E-segment. In 2018, Volvo launched the second generation. It takes up the style of its older sister V90, with which it shares the mechanics, except for the air suspension, which is not available on the V60.
Contents
How To Reset Maintenance Service Light on Volvo V60 (2011-2021)
When the Maintenance Overdue message appears in the display, it’s time for regular service at the workshop. The system must be reset after performed the maintenance service on your vehicle. Depending on your vehicle model, here are a few ways to reset the maintenance light on Volvo V60:
1st Generation (2011-2018)
There are 2 ways to reset the service light on the second generation of the Volvo V60 (2011 2012 2013 2014 2015 2016 2017 2018). Both use different methods. Depending on your vehicle model year, here’s how to do it:
With Cluster Button
Time needed: 7 minutes
Follow the instructions below if your vehicle is equipped with a Trip button on the instrument cluster.
- Turn off the ignition and close all the doors
Make sure your vehicle is stopped in a safe place
- Place the ignition to the position I
If your vehicle has the keyless starting system, keep the remote key into the ignition slot, press the START/STOP ENGINE button once
- Trip mode needs to be on TRIP 2 or T2
Press the T1/T2 button on cluster to select the trip mode
- Hold down the T1/T2 button and then place the ignition to the position II
If your vehicle has the keyless starting system, keep press the T1/T2 button while holding the START/STOP ENGINE button for 2 seconds
- Keep holding the T1/T2 button until the ⓘ indicator blinks
Release the T1/T2 button when the ⓘ indicator flashes 3 times
- Verify the indicator has been reset by shut off the car and then starting the engine
Done!
With Turn Signal Lever
Follow these instructions if your vehicle is equipped with a control button on the turn signal lever.
- Keep the remote key into the ignition slot and then press the START/STOP ENGINE button briefly
- Use the thumbwheel on the turn signal lever to select Trip 2 or T2
- Press and hold the OK button on the end of the lever while holding the START/STOP ENGINE button
- Keep holding the OK button until the ⓘ indicator blinks
- Release both buttons when you hear a chime
- Verify the indicator has been reset by starting the engine
2nd Generation (2019-2021)
Unlike the previous generation, you can reset the maintenance light using the Cruise Control button on the steering wheel in this latest generation (2019 2020 2021). Follow these steps:
- Turn off the ignition and close all doors
- Place the ignition to the position I by turn the START knob clockwise and release it
- Press and hold the (-) REDUCE SPEED button while starting the engine
- Keep hold the (-) REDUCE SPEED button until the ℹ️ indicator blinks
- Release the button when the ℹ️ indicator flashes 3 times
- If successful, a Maintenance Reminder Reset message will appear on the screen
These instructions are based on the Volvo V60 owner’s manual. This procedure should apply to the first and second generations of the Volvo V60 (2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 2021 model years). Hopefully, the article How To Reset Maintenance Service Light on Volvo V60 (2011-2021) can solve your problem. Good Luck!
Leave a Reply