How To Reset Peugeot 308 Tyre Pressure Warning Light (2013-2020)

Last Updated on January 20, 2020 by Christ

How To Reset Peugeot 308 Tyre Pressure Warning Light (2013-2020) – The Peugeot 308 is a car of the C segment produced in two series from 2007 by French automaker Peugeot. Heir to the Peugeot 307 produced from 2001 to 2009 (including the DC version), the 308 was the first car in Sochaux House to maintain unchanged its name in the transition from one generation to another. When the career of the first 308 series was still full, the senior executives of the PSA Group wondered what designation should have the heir of that model.

The logic would have liked the initials 309 but had already belonged to a previous Peugeot model. Therefore, it was chosen to leave the acronym 308 intact and indeed changed the denomination criterion of future models, which would keep the 8 as the last figure for the models to be marketed in the already established markets and the 1 for the models intended for the markets in Way of development. In any case, the 308 is a family car, although existed versions with very high-performance engines: the first series was more daring in design, while the second is soberer.

How To Reset Peugeot 308 Tyre Pressure Warning Light (2013-2020)

Contents

How To Reset Peugeot 308 Tyre Pressure Warning Light (2013-2020):

Time needed: 7 minutes

If you replaced a wheel, tire, TPMS sensor, etc. and are now getting a warning light on your car, then the sensor needs to be reset. To reset the Tire Pressure Monitoring System (TPMS) light on your 2013 2014 2015 2016 2017 2018 2019 2020 Peugeot 308, follow these steps:

  1. Stop the vehicle in a safe place and turn the engine switch off

  2. Adjust the tire inflation pressure recommended on the tire placard located on the middle pillar, driver’s side.

  3. Turn the engine switch to the “ON” position

  4. Press the DRIVING / VEHICLE button on the touch screen display

    Peugeot tyre pressure reset button

  5. Select DRIVING FUNCTION tab

  6. Select “Under-inflation initialisation”.

  7. Select “Yes” to Confirm

With the Audio System:

  • Stop the vehicle in a safe place and turn the engine switch off
  • Adjust the tire inflation pressure recommended on the tire placard located on the middle pillar, driver’s side.
  • Turn the engine switch to the “ON” position
  • Press the MENU button located on the audio system
  • Highlight the  Personalisation-configuration menu by pressing the “<<” or “>>” button
  • Press the “OK” button
  • In the Personalisation, menu select Define the vehicle parameters
  • Press the “OK” button to confirm
  • select the Driving Assistance menu
  • Select Tyre pressures menu
  • Then select the Reinitialization menu
  • Press the “OK” button to confirm

With SET button:

  • Make sure the vehicle is at a complete stop
  • Turn the engine switch off
  • Adjust the tire inflation pressure recommended on the tire placard located on the door panel.
  • Turn the ignition to ON position without starting the engine.
  • Locate and press the SET button until you hear an audible signal
Reset Low Tyre Pressure Peugeot

For more details, please watch the following video:

This tutorial is based on the Peugeot owner’s manual. The procedure above can be applied to the latest generations of Peugeot 308 (2013 2014 2015 2016 2017 2018 2019 2020 model years, which is equipped with a Tyre Pressure Monitoring System (TPMS). Hopefully, the article How To Reset Peugeot 308 Tyre Pressure Warning Light (2013-2020) useful for you.

(Visited 5,423 times, 1 visits today)

1 Comment on “How To Reset Peugeot 308 Tyre Pressure Warning Light (2013-2020)

  1. I am trying to reset the tyres pressure but it is not working … I have set them on 35 PSI anr rear tyres on 33 but still showing the same problem .
    What is the solutions to fix it ?

Leave a Reply

Your email address will not be published. Required fields are marked *

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.