How to Reset 2018 Chevrolet Cruze Tire Pressure TPMS Light

How to Reset 2018 Chevrolet Cruze Tire Pressure TPMS Light – The Chevrolet Cruze is a medium-sized car produced in 2009 by the Korean automaker Daewoo (now GM Korea as part of the US group General Motors). The car replaces the Chevrolet Nubira in Europe while in the Asian markets it is sold under the name Daewoo Lacetti Premiere and in Australia, it is known as Holden Cruze.

In 2014, the Cruze exceeded two million cars sold worldwide. The engine range of the Cruze consists of three petrol engines plus a bi-fuel variant produced in Italy by BRC, and a turbodiesel engine designed by VM Motori under the name of RA 420 SOHC thanks to an agreement made in 2005 with GM. Currently, this engine is not part of the VM production but is produced under license by GM-Daewoo and Hyundai Motor Company. in versions suitable for the respective applications.

How to Reset 2018 Chevrolet Cruze Tire Pressure TPMS Light

How to Reset 2018 Chevrolet Cruze Tire Pressure TPMS Light:

If you receive a low-tire-pressure monitoring system (TPMS) warning light while driving and you want to clear or turning off the warning light on your 2016 2017 2018 2019 Chevrolet Cruze, follow these instructions:

  • Make sure the vehicle is at a complete stop
  • Turn the engine switch off
  • Adjust the tire inflation pressure recommended on the tire placard located on the door panel.
  • Driving for a few miles (kilometers), calibration will complete after 2 minutes of cumulative driving at 20 mph (32 km/h).

If you replaced a wheel, tire, TPMS sensor etc. and are now getting a warning light on your car, then the sensor needs to be reset. To relearn or reset the Tire Pressure Monitoring System (TPMS) sensor on your 2015 2016 2017 2018 2019 Chevrolet Cruze you must have a TPMS relearn tool and follow these steps:

  • Stop the vehicle in a safe place and turn the engine switch off and engage the parking brake.
  • Place the vehicle in Service Mode by pressing and holding ENGINE START/STOP for more than five seconds without depressing the brake pedal.
  • If your vehicle has a base level DIC:
    • Press MENU on the turn signal lever until the VEHICLE menu is displayed
    • Use the thumbwheel to scroll to the Tire Pressure Menu
    • Press the SET/CLR button to begin the sensor matching process.
    • Press the SET/CLR button again to confirm
    • The horn sounds twice to signal the receiver is in relearn mode
  • If the vehicle has an uplevel DIC:
    • Use the DIC controls on the right side of the steering wheel to scroll to the Tire Pressure Menu
    • Press the button to begin the sensor matching process.
    • Press the button again to confirm
    • The horn sounds twice to signal the receiver is in relearn mode
  • Starting from the driver’s side front tire, place the relearn tool against the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor.
  • Repeat the procedure on the right-front tire, the right rear tire, and the last one left rear tire.
  • A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.
  • Turn the ignition off and start the engine to verify the indicator has been reset.

For more details, please watch the following video:

This procedure should be work on the latest generation of Chevrolet Cruze (2015 2016 2017 2018 2019 model years). Hopefully, the article of How to Reset 2018 Chevrolet Cruze Tire Pressure TPMS Light useful for you.

(Visited 26 times, 1 visits today)
Tagged with: , , , ,

Leave a Reply

Your email address will not be published. Required fields are marked *

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.