Car

How To Reset Chevy Impala TPMS Low Tire Pressure Light (2014-2020)

How To Reset Chevy Impala TPMS Low Tire Pressure Light (2014-2020) – The Chevrolet Impala is a car produced by the American manufacturer Chevrolet since 1959 for the North American market. The first Impala was presented at the Motorama exhibition of General Motors in 1956. These versions showed their new line of vehicles for next year.

This first Impala was a coupe for four passengers, with “a strong Corvette flavor”, which was called Corvette Impala. The show car was made with a fiberglass body, like the Corvette. This car takes its name from an artiodactyl mammal called Impala. In 2013 at the New York Auto Show in the USA. presented the Impala 2014.

How To Reset Chevy Impala TPMS Low Tire Pressure Light (2014-2020):

If you receive a low-tire-pressure monitoring system (TPMS) warning light while driving and you want to clear or turning off the warning light on your 2014 2015 2016 2017 2018 2019 2020 Chevy Impala, follow these instructions:

  1. Make sure the vehicle is at a complete stop
  2. Turn the engine switch off
  3. Adjust the tire inflation pressure recommended on the tire placard located on the door panel.
  4. Driving for a few miles (kilometers), calibration will complete after 2 minutes of cumulative driving at 20 mph (32 km/h).

Time needed: 7 minutes

If you replaced a wheel, tire, TPMS sensor, etc. and are now getting a warning light on your car, then the sensor needs to be reset. To relearn or reset the Tire Pressure Monitoring System (TPMS) sensor on your 2014 2015 2016 2017 2018 2019 Chevy Impala you must have a TPMS relearn tool and follow these steps:

  1. Stop the vehicle in a safe place and turn the engine switch off and engage the parking brake.

  2. Place the vehicle in Service Mode by pressing and holding ENGINE START/STOP for more than five seconds

  3. Use the five-way DIC control on the right side of the steering wheel to scroll to the Tire Pressure screen under the DIC info page.

  4. Press and hold the  button until the horn sounds twice to signal the receiver is in relearn mode

  5. Starting from the driver’s side front tire, place the relearn tool against the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor.

  6. Repeat the procedure on the right-front tire, the right rear tire, and the last one left rear tire.

  7. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.

  8. Turn the ignition off and start the engine to verify the indicator has been reset.

This tutorial is based on the Chevrolet owner’s manual. This procedure should be work on the latest generation of the Chevy Impala (2014 2015 2016 2017 2018 2019 2020 model years). Hopefully, the article of How To Reset Chevy Impala TPMS Low Tire Pressure Light (2014-2020) useful or you. Good Luck!

Christ

Recent Posts

Exploring the Tech-Advanced Safety Features of Honda Civic

When it comes to safety on the roads, nothing beats the sterling integration of technology…

1 year ago

Mastering Car Oil Changes: Crucial for Business Efficiency

Imagine a car engine as the heart of a business. Without proper and regular maintenance,…

1 year ago

Avoiding Common Car Maintenance Mistakes

Maintaining the health of your car is much like maintaining your health. Ignoring minor symptoms…

1 year ago

Petrol vs Diesel: Unravelling the Used Jeep Wrangler Conundrum

The quest to find the perfect engine variant, when in the market for a used…

1 year ago

Mastering DIY Checks for a Used Jeep Wrangler

When it comes to advancing your automotive acumen, understanding the ins and outs of purchasing…

1 year ago

Key Maintenance Tips for Used Jeep Wranglers

Jeep Wranglers, known for their robust character and off-road prowess, can prove to be resilient…

1 year ago

This website uses cookies.