How To Reset Nissan Quest ECU Check Engine Light (2003-2017)

Last Updated on December 17, 2019 by Christ

How To Reset Nissan Quest ECU Check Engine Light (2003-2017) – Nissan released Nissan Quest at the LA Auto Show 2010. Nissan Quest marketed in early 2011 for the US market. Quest shares a platform with the Nissan Elgrand. Nissan instills a V6 engine, 3500 ccs, which bursts power 253 hp and 320 Nm of torque. The engine is combined with the Xtronic CVT transmission.

This luxurious MPV consists of three rows of seats with electric sliding doors. The second and third-row seats can be folded flat. There is a VGA screen 8 “on the dashboard, DVD entertainment system, two wireless headphones, and remote control, and monitor 11” on the back for your kid’s DVD set. Nissan said Quest presented to woo the parents. Nissan calls it Parenting Job.

How To Reset Nissan Quest ECU Check Engine Light (2003-2020)

How To Reset Nissan Quest ECU Check Engine Light (2003-2017):

Time needed: 15 minutes

If you want to turn off or clear the Check Engine Light / ECU light in 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 Nissan Quest, perform the following procedures within the specified time! Because timing is extremely critical.

  1. Turn the ignition key to position “ON” without starting the engine and wait 3 seconds.

  2. Fully press and release the accelerator pedal five times within 5 seconds.

  3. Wait 7 seconds

  4. Fully depress the accelerator pedal all the way to the floor and hold for ten seconds. until the CEL starts blinking.

    At this point, the light CEL should start flashing error code stored in the system and you can release the pedal. If you only get five flashes slowly or not flashing at all, then it is time You went on one of the above steps and you have to start from scratch.

  5. Fully release the accelerator pedal (while the CEL is still blinking) and wait about 10 seconds.

  6. Fully depress the accelerator pedal and keep it for more than 10 seconds.

  7. Fully release the accelerator pedal (The CEL light will continue to blink).

  8. Turn the ignition off and start the engine to verify the indicator has been reset.

For more details, please watch the following video:

Note: Repeat the process, if the lights still illuminate when you start the engine. Timing is EXTREMELY critical to resetting the ECU. This tutorial is based on the Nissan repair manual. This procedure should be work on all generations of Nissan Quest ( 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 model years). Hopefully the article of How To Reset Nissan Quest ECU Check Engine Light (2003-2017) useful for you. Good Luck!

(Visited 5,017 times, 1 visits today)

2 Comments on “How To Reset Nissan Quest ECU Check Engine Light (2003-2017)

  1. I have a 2006 quest that I did the timing chain on…. after reassembling the van. Ive lost throttle response. Codes p2101,p2100 appears. Ive cleared it, did all the steps to reset the throttle, gas pedal, and ecu…. ive rechecked and double checked all connections to and from the van…. please help me with any input you may have or similar problems so i know where to look next. I’m basically stumped for the moment…. oh after doing the reset steps. I might get a small responses that will allow the engine to reach 2k rpm… but after repeating the steps it’ll go back to normal or stay at the response after the reset process.. please help with any information…. thank you for your time

  2. I followed the instruction with the timer and was precise but my CES light do not blink. I have 2017 Nissan Quest. My husband use to do all the work on the car but since his brain surgery he is unable to.

Leave a Reply

Your email address will not be published. Required fields are marked *

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.